QUESTIONS and FACT SHEET

There are some variations between films - see our product comparison sheet for details.

1. AVAILABLE IN SHEETS OR ROLLS
2. WIDTHS AVAILABLE UP TO 81" WIDE
3. TYPE 1 BONDS NOW AVAILABLE
4. PERFORATED IF NEEDED
5. CAN BE FIRE RETARDED
6. NON-SLIP AVAILABLE
7. SAFE - USER FRIENDLY

1. No Formaldehyde
2. No V.O.C.'s
3. No Fumes or Odors
4. No Glue Rolls
5. No Wash Up
6. No Special Storage Conditions
7. No Shelf Life Problems
8. No Bleed Through

8. GUARANTEED QUALITY

1. Injected, Extruded Calandered, Blown, Cast to be the Same Every Time
2. 100% Solid Glue
3. Enormous Shelf Life (Still Testing - Have Not Found Limit)
4. No Mixing

9. CLEAR FILM ADHESIVE

1. Invisible Edge
2. Can be Colored

10. DOES NOT BLEED THRU MICRO THIN FACES AND OVERLAYS
11. NOT EFFECTED BY MOST FINISHES
12. EXTREMELY GOOD BARRIER TO FORMALDEHYDE VAPORS AND H20
13. NOT EFFECTED BY H20
14. ELIMINATES PRECURE
15. MOST CAN BE REPRESSED OR RENIPPED TO MINIMIZE REJECTS
16. CAN BE PREAPPLIED FOR LATER PRESSING OR PROCESSING

1. In most cases, strengthens Thin Veneers by Over 1000% - Both Width and Across Grain. (Elmendorf Test)
2. Stabilizes
3. Flattens
4. Enhances

17. REDUCES REJECTS
18. EASILY GLUES TREATED CROTCHES/BURLS AND EXOTIC HARD TO GLUE WOOD SPECIES.
19. BONDS METALLIC FOILS, METALS, ALUMINUM, GLASS, CERAMICS, MOST VINYL, FABRICS, RUBBER, LEATHER, HIGH PRESSURE PLASTIC. MDF. L30, FOAM, NON-WOVEN FABRIC, POLYCARBONATE, ABS, POLYAMIDE, PVC, SBR, NEOPRENE, CELLULOSE, ACETATE, ETC.
20. FACES (VENEERS) BACKED WITH 2 MIL DRIBOND CAN BE FLEXED TO WRAP AROUND THE DIAMETER OF A PENCIL.
21. COMPATIBLE WITH HIGH FREQUENCY ELECTRONIC EQUIPMENT

1. Allows Use of Normal Moisture Content (7-9%) - Veneer has Less Cracking and Better Bends
2. Adds Stability to Shapes

22. ULTRASONIC + IMPULSE COMPATIBLE
23. WILL NOT BOND TO TEFLON OR SOME SILICON
24. EASY TO USE

(160°-325° F ~ 13 to 150 PSI) High speed bond - Fast parse cycles

25. EXCELLENT TEST RESULTS

1. Shear - M.O.E. - Internal Bond - M.O.R.
2. 3 Cycle Soak
3. 3 Cycle Boil
4. Wash
5. Dry clean

26. COMPATIBLE WITH WET GLUE LINES IN THE SAME PANEL WITH DRIBOND® ADHESIVE FILM UNDER THE FACE OR OVERLAY.
27. SAWS AND MACHINES CLEAN
28. IS NOT ABRASIVE
29. NO GLUE SQUEEZE OUT
30. AVAILABLE IN ROLLS OR SHEETS
31. LAY UP CAN BE DONE HOURS OR DAYS AHEAD OF TIME
32. CREATES A VERY TOUGH BUT NON BRITTLE GLUE LINE
33. CAN BE REPRESSED OR RENIPPED AT HIGH (325 F) TEMPERATURES FOR THICK SANDWICH CONSTRUCTION, WITH NO DELAMINATION.
34. DRIBOND BACKED VENEERS OR OVERLAYS CAN BE SANDED, POLISHED, FLEXED OR TENDERIZED
35. MINIMIZES THE EFFECT OF HUMIDITY CHANGES
36. REDUCES LIABILITIES (Increases Product & Worker Safety)
37. LOW DENSITY FOAMS EASILY FUSED TO MOST ANY SURFACE - NO FOAM DEGRADE

No Pinch Roll, No Wash Water (E.P.A.), No Formaldehyde

1. BECAUSE THEY DO NOT WANT TO BE LEFT BEHIND IN PRODUCT QUALITY OR SAFETY OR COST.

2. BECAUSE IT IS DIFFICULT TO EXPLAIN TO A SERIOUSLY INJURED EMPLOYEE THE REASON YOUR COMPANY STILL USES UNNECESSARILY DANGEROUS GLUING METHODS.

3. BECAUSE IT IS DIFFICULT TO EXPLAIN TO A CUSTOMER WHY HIS PRODUCT SMELLS THE WAY IT DOES AND HOW IT MIGHT BE AFFECTING HIS HEALTH.

4. BECAUSE IN MOST CASES AN ACCURATE COST MODEL PROVES IT IS BENEFICIAL TO THE BOTTOM LINE. DRIBOND® NOW AS LOW AS 1.7 CENTS PER SQUARE FOOT ADHESIVE COST.